Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected
by the drive itself and contains data that the manufacturer considered relevant to check reliability.
The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data,
and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is
considered unreliable and likely to fail. By using several techniques, this report tries to give a wider
range of information, basing its analysis on advanced comparisons with normal values based on real
hard disks and on expert-like checks. The final results are not to be taken as an absolute truth, but
they are almost as good as a professional expert advice about your hard disk status.
Your hard disk is a WDC WD20EARX-00PASB0 with firmware 51.0AB51.
The average temperature for this hard disk model is 31°C (min=23°C max=41°C) and yours is 22°C.
All the attributes of your hard disk are above the S.M.A.R.T. thresholds set by the manufacturer. This is good.
BLOCKING ISSUE : your hard disk has 5 pending sectors. Those are sectors that couldn't be properly read and that the hard disk logic is waiting for a write operation to try to remap to a spare sector (if available). According to the Reallocated Sector Count attribute, your hard disk seems to have available spare sectors. A simple disk surface scan won't be enough to force the remap operation. You need a read/write surface scan to remap the sector. The best option should be a tool that knows about what should be read from that sector so that it has some option to apply the best fix to the missing data.
NOTE : your hard disk Power On Hours Count attribute current value (92) is below the normal range (95 - 100) reported for your specific hard disk model. Basically your hard disk was powered on for more than the maximum time the average user did. This means that either all of the reports collected are from hard disks that were not powered on for too long (this is realistic for recent models) or that your hard disk is becoming old. Usually this is not considered as a pre-failure advisory, but you should check whether you want to replace the hardware or keep an eye on its performances over time.
The overall fitness for this drive is 0%.
The overall performance for this drive is 100%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
DISCLAIMER: this report does its best to highlight issues and warnings related to your hard disk. It cannot be held responsible for any mistake. This page and its results cannot be used in any other way but the one defined by its author.
The average temperature for this hard disk model is 31°C (min=23°C max=41°C) and yours is 22°C.
| Attribute | Current | Raw | ||||
|---|---|---|---|---|---|---|
 |
Raw Read Error Rate | 200 | 000000000047 | |||
|
Spin Up Time | 252 | 000000000936 | |||
 |
Start/Stop Count | 99 | 0000000004D0 | |||
|
Reallocated Sector Count | 200 | 000000000000 | |||
|
Seek Error Rate | 200 | 000000000000 | |||
|
Power On Hours Count | 92 | 000000001950 | |||
|
Spin Retry Count | 100 | 000000000000 | |||
|
Calibration Retry Count | 100 | 000000000000 | |||
|
Power Cycle Count | 100 | 0000000002AB | |||
|
Power Off Retract Count | 200 | 0000000000D4 | |||
 |
Load Cycle Count | 196 | 000000003209 | |||
|
Reallocated Event Count | 200 | 000000000000 | |||
|
Current Pending Sector | 200 | 000000000005 | |||
|
Offline Uncorrectable Sector Count | 200 | 000000000000 | |||
|
Ultra DMA CRC Error Rate | 200 | 000000000000 | |||
|
Write Error Rate | 200 | 000000000000 |
All the attributes of your hard disk are above the S.M.A.R.T. thresholds set by the manufacturer. This is good.
BLOCKING ISSUE : your hard disk has 5 pending sectors. Those are sectors that couldn't be properly read and that the hard disk logic is waiting for a write operation to try to remap to a spare sector (if available). According to the Reallocated Sector Count attribute, your hard disk seems to have available spare sectors. A simple disk surface scan won't be enough to force the remap operation. You need a read/write surface scan to remap the sector. The best option should be a tool that knows about what should be read from that sector so that it has some option to apply the best fix to the missing data.
NOTE : your hard disk Power On Hours Count attribute current value (92) is below the normal range (95 - 100) reported for your specific hard disk model. Basically your hard disk was powered on for more than the maximum time the average user did. This means that either all of the reports collected are from hard disks that were not powered on for too long (this is realistic for recent models) or that your hard disk is becoming old. Usually this is not considered as a pre-failure advisory, but you should check whether you want to replace the hardware or keep an eye on its performances over time.
The overall fitness for this drive is 0%.
The overall performance for this drive is 100%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
DISCLAIMER: this report does its best to highlight issues and warnings related to your hard disk. It cannot be held responsible for any mistake. This page and its results cannot be used in any other way but the one defined by its author.